Congratulations on your purchase of the Electro-Harmonix Tone Corset. The Tone Corset is an analog compressor/sustainer that allows for extreme or subtle control of the dynamics of your instrument. There are controls for setting the output volume, sustain/compression, attack, blend amount and pad switch.
Note: The TONE CORSET draws up to 9mA at 9VDC with a center negative plug or runs off a 9 Volt battery. If using an adaptor make sure to use one with the correct polarity. Failure to do so may damage your TONE CORSET and void the warranty. Please use an Electro-Harmonix 9.6DC-200mA power supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA) which is sold separately.
VOLUME KNOB: Adjusts the output level of the effect
SUSTAIN KNOB: Controls the amount of the compression
ATTACK KNOB: Controls how quickly the compressor will recover
BLEND KNOB: Adjusts the mix of the dry and compressed signal set to the output
PAD SWITCH: Pads down the input signal to prevent undesirable distortion
BYPASS FOOTSWITCH & STATUS LED
The Footswitch selects whether the Tone Corset is engaged or in True Bypass mode. When the effect is engaged, the LED is lit.
The ¼” jack is the audio input for the Tone Corset. The input impedance is 1MΩ.
The ¼” jack is the audio out for the Tone Corset. The output impedance is 100Ω.
CHANGING THE BATTERY
To change the 9-volt battery, you must remove the 4 screws on the bottom of the Tone Corset. Once the screws are removed, you can take off the bottom plate and change the battery. Please do not touch the circuit board while the bottom plate is off or you risk damaging a component. To extend battery life, disconnect the INPUT jack when the Tone Corset is not in use.
- WARRANTY INFORMATION -
Please register online at http://www.ehx.com/product-registration or complete and return the enclosed warranty card within 10 days of purchase. Electro-Harmonix will repair or replace, at its discretion, a product that fails to operate due to defects in materials or workmanship for a period of one year from date of purchase. This applies only to original purchasers who have bought their product from an authorized Electro-Harmonix retailer. Repaired or replaced units will then be warranted for the unexpired portion of the original warranty term. If you should need to return your unit for service within the warranty period, please contact EHX Customer Service at 718-937-8300 or email@example.com for a Return Authorization Number. Along with your pedal, please include a brief description of the problem as well as your name, address, telephone number, copy of your receipt, and a check or money order.
United States - $12
Canada - $15
Europe and outside countries - $25
C/O New Sensor Corporation
Attn: Service Department
55-01 2nd Street
Long Island City, NY, 11101
Please make checks/money orders payable to New Sensor Corporation.
To hear demos on all EHX pedals visit us on the web at www.ehx.com
Email us at firstname.lastname@example.org
- FCC COMPLIANCE -
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the device is not installed and used in accordance with the instructions, it may cause harmful interference to radio communications and void the user’s authority to guarantee the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment under FCC rules.